takeanumbr's Photobucket media

Dash clips available on ebay all the time.

takeanumbr — Thu, 8 Oct 2009 08:40:52 MDT

takeanumbr posted a photo

Dash clips available on ebay all the time. - DSC00758.jpg

DSC01977.jpg

takeanumbr — Sun, 26 Apr 2009 12:30:59 MDT

takeanumbr posted a photo

DSC01977.jpg

Distributor gear wear using tight lash street solid roller cam, and stock oil pump.

takeanumbr — Sun, 26 Apr 2009 12:30:08 MDT

takeanumbr posted a photo

Distributor gear wear using tight lash street solid roller cam, and stock oil pump. - DSC01978.jpg

Three pictures of 12k mile wear on the MSD bronze distributor gear.

takeanumbr — Sun, 26 Apr 2009 12:29:20 MDT

takeanumbr posted a photo

Three pictures of 12k mile wear on the MSD bronze distributor gear. - DSC01980.jpg

Clutch MS rod attachment. Way more than the suggested 12:1 ratio.

takeanumbr — Sat, 28 Mar 2009 10:11:31 MDT

takeanumbr posted a photo

Clutch MS rod attachment. Way more than the suggested 12:1 ratio. - RodAttach.jpg

The shifter opening I cut for the TKO trans.

takeanumbr — Sat, 28 Mar 2009 10:08:27 MDT

takeanumbr posted a photo

The shifter opening I cut for the TKO trans. - DSC00332.jpg

Hard to see exactly, but this pic gives a slight idea of the engine/driveline angle with the engine and TKO.

takeanumbr — Fri, 27 Mar 2009 09:28:04 MDT

takeanumbr posted a photo

Hard to see exactly, but this pic gives a slight idea of the engine/driveline angle with the engine and TKO. - EngAngle.jpg

A real sloppy job of sealing the gaps between the new tunnel and the old that I had to cut away for the TKO housing.

takeanumbr — Fri, 27 Mar 2009 09:27:19 MDT

takeanumbr posted a photo

A real sloppy job of sealing the gaps between the new tunnel and the old that I had to cut away for the TKO housing. - Tunnel.jpg

Dash clips that holds the dash. Ebay has them.

takeanumbr — Tue, 4 Nov 2008 08:46:35 MST

takeanumbr posted a photo

Dash clips that holds the dash. Ebay has them. - 34ef8c87.jpg

I'm printing the bottom proof/sticker for my Torino.

takeanumbr — Thu, 9 Oct 2008 10:22:27 MDT

takeanumbr posted a photo

I'm printing the bottom proof/sticker for my Torino. - ee7a1976.jpg

My 1st time to race. I installed an NX system, these slips are without nitrous and then with.

takeanumbr — Mon, 1 Sep 2008 10:04:54 MDT

takeanumbr posted a photo

My 1st time to race. I installed an NX system, these slips are without nitrous and then with. - c6b7d569.jpg

Excellent service from this vendor to repair my ribbon tach.

takeanumbr — Sun, 17 Aug 2008 10:36:55 MDT

takeanumbr posted a photo

Excellent service from this vendor to repair my ribbon tach. - TachRepairReciet.jpg

Adjust valve lash at 8500 miles. Intake was loose .005, ex .003 over specs. Not bad.

takeanumbr — Sun, 10 Aug 2008 10:15:08 MDT

takeanumbr posted a photo

Adjust valve lash at 8500 miles. Intake was loose .005, ex .003 over specs. Not bad. - DSC00594.jpg

Felpro gasket fills the gap between intake and block.

takeanumbr — Wed, 9 Jul 2008 09:13:51 MDT

takeanumbr posted a photo

Felpro gasket fills the gap between intake and block. - HPIM0572.jpg

The gap between intake and block.

takeanumbr — Wed, 9 Jul 2008 09:11:59 MDT

takeanumbr posted a photo

The gap between intake and block. - HPIM0542.jpg

MOV01066.flv

takeanumbr — Wed, 9 Jul 2008 08:17:22 MDT

takeanumbr posted a video

MOV01066.flv

Degree the new cam

takeanumbr — Sun, 29 Jun 2008 09:01:33 MDT

takeanumbr posted a photo

Degree the new cam - HPIM0104.jpg

Tremec TKO 600 to 545ci test fit.

takeanumbr — Sat, 28 Jun 2008 15:36:21 MDT

takeanumbr posted a photo

Tremec TKO 600 to 545ci test fit. - McLeodStuff4.jpg

McLeod StreetTwin Clutch.

takeanumbr — Sat, 28 Jun 2008 15:36:20 MDT

takeanumbr posted a photo

McLeod StreetTwin Clutch. - McLeodStuff3.jpg

McLeod flywheel w/ARP flexplate bolts.

takeanumbr — Sat, 28 Jun 2008 15:36:19 MDT

takeanumbr posted a photo

McLeod flywheel w/ARP flexplate bolts. - McLeodStuff2.jpg

New McLeod Clutch, bellhousing, and hydraulic TO bearing.

takeanumbr — Sat, 28 Jun 2008 15:36:18 MDT

takeanumbr posted a photo

New McLeod Clutch, bellhousing, and hydraulic TO bearing. - McLeodStuff.jpg

Part number for the poly isolators I used for the Torino

takeanumbr — Thu, 17 Apr 2008 08:27:41 MDT

takeanumbr posted a photo

Part number for the poly isolators I used for the Torino - HPIM1015.jpg

The poly is shorter in length, but are othe dimensions are good.

takeanumbr — Thu, 17 Apr 2008 08:27:35 MDT

takeanumbr posted a photo

The poly is shorter in length, but are othe dimensions are good. - HPIM1020.jpg

I had to cut off the rise and leave a nub just large enough to fit the hole in the leaf spring plate. Very easy to do.

takeanumbr — Thu, 17 Apr 2008 08:27:29 MDT

takeanumbr posted a photo

I had to cut off the rise and leave a nub just large enough to fit the hole in the leaf spring plate. Very easy to do. - HPIM1022.jpg

My nifty fast idle thing. An Edelbrock a/c idle compenstor does a great job for cold fast idle start-ups.

takeanumbr — Sun, 6 Apr 2008 10:11:34 MDT

takeanumbr posted a photo

My nifty fast idle thing. An Edelbrock a/c idle compenstor does a great job for cold fast idle start-ups. - DSC00591.jpg

Flowmaster offers a great universal 3" exhaust kit. Obviously, this must go behind the 545ci!

takeanumbr — Sun, 6 Apr 2008 10:10:43 MDT

takeanumbr posted a photo

Flowmaster offers a great universal 3" exhaust kit. Obviously, this must go behind the 545ci! - DSC00569.jpg

Extra fuse block for extra added stuff.

takeanumbr — Sun, 6 Apr 2008 10:09:53 MDT

takeanumbr posted a photo

Extra fuse block for extra added stuff. - DSC00556.jpg

The K&N Extremefilter is about the only filter setup I liked with the stang shaker.

takeanumbr — Sun, 6 Apr 2008 10:01:20 MDT

takeanumbr posted a photo

The K&N Extremefilter is about the only filter setup I liked with the stang shaker. - DSC00546.jpg

The mustang shaker scoop adds just enough room for the K&N Extreme filter setup.

takeanumbr — Sun, 6 Apr 2008 10:00:29 MDT

takeanumbr posted a photo

The mustang shaker scoop adds just enough room for the K&N Extreme filter setup. - DSC00484.jpg

Yes, a mustang shaker scoop.

takeanumbr — Sun, 6 Apr 2008 09:59:39 MDT

takeanumbr posted a photo

Yes, a mustang shaker scoop. - DSC00478.jpg

Yeah, the Torino enthusiast are going to just love this!LOL!!

takeanumbr — Sun, 6 Apr 2008 09:35:29 MDT

takeanumbr posted a photo

Yeah, the Torino enthusiast are going to just love this!LOL!! - DSC00476.jpg

I fabbed a black metal box to mount the shifter boot/plate, and attached it to the floor.

takeanumbr — Sun, 6 Apr 2008 09:34:39 MDT

takeanumbr posted a photo

I fabbed a black metal box to mount the shifter boot/plate, and attached it to the floor. - DSC00470.jpg

Another look at the shifter.

takeanumbr — Sun, 6 Apr 2008 09:33:53 MDT

takeanumbr posted a photo

Another look at the shifter. - DSC00468.jpg

Yes, don't look at the green interior, red exterior. Hey...it's a "do what the hell I want!!" car.

takeanumbr — Sun, 6 Apr 2008 09:25:44 MDT

takeanumbr posted a photo

Yes, don't look at the green interior, red exterior. Hey...it's a "do what the hell I want!!" car. - DSC00466.jpg

I like the look and fit of the new Hurst shifter.

takeanumbr — Sun, 6 Apr 2008 09:24:56 MDT

takeanumbr posted a photo

I like the look and fit of the new Hurst shifter. - DSC00465.jpg

Added an accessory fuse block using ATC type fuses, switched by a relay w/diode.

takeanumbr — Sun, 6 Apr 2008 09:24:10 MDT

takeanumbr posted a photo

Added an accessory fuse block using ATC type fuses, switched by a relay w/diode. - DSC00734.jpg

2003 cobra hydroboost in place of the old vacuum booster.

takeanumbr — Fri, 29 Feb 2008 21:45:07 MST

takeanumbr posted a photo

2003 cobra hydroboost in place of the old vacuum booster. - DSC00575.jpg

A cluttered pic of the hydroboost with the new 545ci installed.

takeanumbr — Fri, 29 Feb 2008 06:30:24 MST

takeanumbr posted a photo

A cluttered pic of the hydroboost with the new 545ci installed. - DSC00405-1.jpg

Just enough clearance that I can remove the VC.

takeanumbr — Fri, 29 Feb 2008 06:29:35 MST

takeanumbr posted a photo

Just enough clearance that I can remove the VC. - DSC00398.jpg

About 3/16" clearance between the MC/hydroboost and valvcover.

takeanumbr — Fri, 29 Feb 2008 06:28:46 MST

takeanumbr posted a photo

About 3/16" clearance between the MC/hydroboost and valvcover. - DSC00396.jpg

I had to cut off the MC and hydroboost mount ears to clear the valve cover.

takeanumbr — Fri, 29 Feb 2008 06:21:44 MST

takeanumbr posted a photo

I had to cut off the MC and hydroboost mount ears to clear the valve cover. - DSC00392.jpg

I installed a hydroboost from a 2003 Cobra

takeanumbr — Fri, 29 Feb 2008 06:20:54 MST

takeanumbr posted a photo

I installed a hydroboost from a 2003 Cobra - DSC00415.jpg

Lots of room to work on the Hooker headers, thanks to the shock tower mods.

takeanumbr — Sat, 16 Feb 2008 09:27:24 MST

takeanumbr posted a photo

Lots of room to work on the Hooker headers, thanks to the shock tower mods. - DSC00401.jpg

First trial fit of McLeod clutch master cylinder.

takeanumbr — Sat, 16 Feb 2008 09:20:36 MST

takeanumbr posted a photo

First trial fit of McLeod clutch master cylinder. - DSC00383.jpg

Lots of room on the passenger side.

takeanumbr — Sat, 16 Feb 2008 09:19:48 MST

takeanumbr posted a photo

Lots of room on the passenger side. - DSC00377.jpg

Lots of room after the shock tower mod. Drivers side.

takeanumbr — Sat, 16 Feb 2008 09:19:02 MST

takeanumbr posted a photo

Lots of room after the shock tower mod. Drivers side. - DSC00376.jpg

Had to cut the radiator support to get the engine and transmission dropped in place.

takeanumbr — Sat, 16 Feb 2008 09:15:17 MST

takeanumbr posted a photo

Had to cut the radiator support to get the engine and transmission dropped in place. - DSC00368.jpg

Couldn't get a very good angle on my new engine leveler.

takeanumbr — Sat, 16 Feb 2008 09:14:31 MST

takeanumbr posted a photo

Couldn't get a very good angle on my new engine leveler. - DSC00364.jpg

Good view of the 545 and Tremec TKO 600, just about to be dropped in.

takeanumbr — Sat, 16 Feb 2008 09:13:50 MST

takeanumbr posted a photo

Good view of the 545 and Tremec TKO 600, just about to be dropped in. - DSC00363.jpg

More room to work on passenger side. Yes I know, dirty engine.

takeanumbr — Sat, 16 Feb 2008 08:11:57 MST

takeanumbr posted a photo

More room to work on passenger side. Yes I know, dirty engine. - DSC00380.jpg

Shock tower modification adds extra space to work with headers/spark plugs. I would absolutely recommend it with a bigblock.

takeanumbr — Sat, 16 Feb 2008 08:11:09 MST

takeanumbr posted a photo

Shock tower modification adds extra space to work with headers/spark plugs. I would absolutely recommend it with a bigblock. - DSC00381.jpg

Shock tower mod done to provide extra room. It's a great improvement!

takeanumbr — Sat, 16 Feb 2008 08:10:20 MST

takeanumbr posted a photo

Shock tower mod done to provide extra room. It's a great improvement! - DSC00405.jpg

Front view of 200 AMP alternator.

takeanumbr — Mon, 31 Dec 2007 23:51:51 MST

takeanumbr posted a photo

Front view of 200 AMP alternator. - DSC00330.jpg

Front view of 200 AMP alternator.

Dyno graph from the Jay Allen cam

takeanumbr — Sat, 20 Jan 2007 17:16:08 MST

takeanumbr posted a photo

Dyno graph from the Jay Allen cam - DynoGraphAllenCam.jpg

A good BFH helps when modifing parts. We now have clearence clearance!

takeanumbr — Sun, 7 Jan 2007 08:13:44 MST

takeanumbr posted a photo

A good BFH helps when modifing parts. We now have clearence clearance! - HPIM0904.jpg

Rt side Hooker 6201\'s hitting the side of the Canton oil pan.

takeanumbr — Sun, 7 Jan 2007 08:10:56 MST

takeanumbr posted a photo

Rt side Hooker 6201\'s hitting the side of the Canton oil pan. - HPIM0902.jpg

First dyno run-643ft lbs torque at 4600rpm

takeanumbr — Fri, 5 Jan 2007 20:08:09 MST

takeanumbr posted a video

First dyno run-643ft lbs torque at 4600rpm - HPIM0920.flv

New cam at idle

takeanumbr — Fri, 5 Jan 2007 20:01:47 MST

takeanumbr posted a video

New cam at idle - HPIM0918.flv

Just fired up the engine with new roller cam.

takeanumbr — Wed, 3 Jan 2007 18:54:52 MST

takeanumbr posted a video

Just fired up the engine with new roller cam. - HPIM0915.flv

Plenty of clearance between timing chain and oil slinger.

takeanumbr — Wed, 3 Jan 2007 18:29:05 MST

takeanumbr posted a photo

Plenty of clearance between timing chain and oil slinger. - HPIM0886.jpg

Another exhaust port.

takeanumbr — Wed, 3 Jan 2007 18:22:18 MST

takeanumbr posted a photo

Another exhaust port. - HPIM0897.jpg

I\'ll need to do some homegrown engineering on these before they will work in my Torino.

takeanumbr — Wed, 3 Jan 2007 18:20:31 MST

takeanumbr posted a photo

I\'ll need to do some homegrown engineering on these before they will work in my Torino. - HPIM0914.jpg

Got my new Hooker 6201\'s. 2 1/8 primary, 3 1/2 collector.

takeanumbr — Wed, 3 Jan 2007 18:17:42 MST

takeanumbr posted a photo

Got my new Hooker 6201\'s. 2 1/8 primary, 3 1/2 collector. - HPIM0912.jpg

Interesting swirl marks on the exhaust port. Too much fuel?

takeanumbr — Wed, 3 Jan 2007 18:15:27 MST

takeanumbr posted a photo

Interesting swirl marks on the exhaust port. Too much fuel? - HPIM0896.jpg

Just degreeing new cam. This is the second cam for this 545ci. Wanted to see if this cam is a little more streetable.

takeanumbr — Wed, 3 Jan 2007 18:13:53 MST

takeanumbr posted a photo

Just degreeing new cam. This is the second cam for this 545ci. Wanted to see if this cam is a little more streetable. - HPIM0883.jpg

Degreed new cam today. Supposed to be Intake open 13.46* at .050. Was 1* off. I\'m not gonna bitch about that.

takeanumbr — Wed, 3 Jan 2007 18:08:57 MST

takeanumbr posted a photo

Degreed new cam today. Supposed to be Intake open 13.46* at .050. Was 1* off. I\'m not gonna bitch about that. - HPIM0881.jpg

no wear on this either

takeanumbr — Mon, 4 Dec 2006 11:16:06 MST

takeanumbr posted a photo

no wear on this either - HPIM0779.jpg

No wear on the oil slinger

takeanumbr — Mon, 4 Dec 2006 11:15:12 MST

takeanumbr posted a photo

No wear on the oil slinger - HPIM0778.jpg

Loaded and taking the 545 to the dyno

takeanumbr — Mon, 13 Nov 2006 07:45:36 MST

takeanumbr posted a photo

Loaded and taking the 545 to the dyno - HPIM0711.jpg

545 on SuperFlow 902 for warmup

takeanumbr — Mon, 13 Nov 2006 07:41:28 MST

takeanumbr posted a video

545 on SuperFlow 902 for warmup - HPIM0727.flv

My phantom II gauges were working fine until the electric temp gauge quit working. It\'s pegged out, past 250F!

takeanumbr — Sun, 24 Sep 2006 20:40:30 MDT

takeanumbr posted a photo

My phantom II gauges were working fine until the electric temp gauge quit working. It\'s pegged out, past 250F! - HPIM0679.jpg

Another crappy video (taken w/my still camera) of the initial startup of the 545.

takeanumbr — Sun, 24 Sep 2006 17:31:08 MDT

takeanumbr posted a video

Another crappy video (taken w/my still camera) of the initial startup of the 545. - HPIM0678.flv

Engine test stand that I built.

takeanumbr — Sun, 24 Sep 2006 17:09:17 MDT

takeanumbr posted a photo

Engine test stand that I built. - HPIM0676.jpg

My 545 on initial start-up on my very homemade engine test stand.

takeanumbr — Sun, 24 Sep 2006 16:13:04 MDT

takeanumbr posted a video

My 545 on initial start-up on my very homemade engine test stand. - HPIM0680.flv

Crites headers from the passenger side

takeanumbr — Tue, 4 Jul 2006 11:47:04 MDT

takeanumbr posted a photo

Crites headers from the passenger side - headrRt.jpg

Crites headers from the drivers side

takeanumbr — Tue, 4 Jul 2006 11:47:02 MDT

takeanumbr posted a photo

Crites headers from the drivers side - headrLt.jpg

Crites 2in headers

takeanumbr — Tue, 4 Jul 2006 11:47:01 MDT

takeanumbr posted a photo

Crites 2in headers - headrFrnt.jpg

oilpump with Canton screen

takeanumbr — Mon, 3 Jul 2006 22:06:58 MDT

takeanumbr posted a photo

oilpump with Canton screen - oilpump.jpg

1971 Torino..soon with a 545ci street engine.

takeanumbr — Sun, 2 Jul 2006 22:04:01 MDT

takeanumbr posted a photo

1971 Torino..soon with a 545ci street engine. - HPIM0370.jpg

getting there

takeanumbr — Sun, 2 Jul 2006 21:55:05 MDT

takeanumbr posted a photo

getting there - eng1.jpg

.081...to tight?

takeanumbr — Sun, 2 Jul 2006 17:18:00 MDT

takeanumbr posted a photo

.081...to tight? - coil.jpg

Victor port matched to the SCJ port

takeanumbr — Fri, 30 Jun 2006 08:44:06 MDT

takeanumbr posted a photo

Victor port matched to the SCJ port - vic3.jpg

looking down the Victor runner from the plenum

takeanumbr — Fri, 30 Jun 2006 08:33:33 MDT

takeanumbr posted a photo

looking down the Victor runner from the plenum - HPIM0402.jpg

Victor runner detail

takeanumbr — Fri, 30 Jun 2006 08:33:32 MDT

takeanumbr posted a photo

Victor runner detail - HPIM0391.jpg

unshrouded valves for a smooth transition

takeanumbr — Fri, 30 Jun 2006 08:33:30 MDT

takeanumbr posted a photo

unshrouded valves for a smooth transition - HPIM0381.jpg

Exhaust bowl blend

takeanumbr — Thu, 29 Jun 2006 09:45:35 MDT

takeanumbr posted a photo

Exhaust bowl blend - ex1.jpg

The BigBlockBoys

takeanumbr — Thu, 29 Jun 2006 09:08:23 MDT

takeanumbr posted a photo

The BigBlockBoys - HPIM0406.jpg

Intake bowl blend

takeanumbr — Thu, 29 Jun 2006 09:08:18 MDT

takeanumbr posted a photo

Intake bowl blend - HPIM0380.jpg